Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
26
www.desatech.com
116035-01B
OPERATING FIREPLACE - Manual Ignition System
For Your Safety Read Before Lighting (cont.)
Lighting Instructions
To Turn Off Gas To Appliance
Manual Lighting Procedure
Operating Hand-Held Remote Operation
OPERATING FIREPLACE
Manual Ignition System (Continued)
•
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don’t try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service techni-
cian to inspect the appliance and to replace any part
of the control system and any gas control which has
been under water.
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information above.
2. Open lower louver panel.
3. Turn off all electric power to the fireplace.
4.
Push in gas control knob slightly and turn clockwise
to “OFF”.
5. Wait five (5) minutes to clear out any gas. Then smell for.
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don’t smell
gas go to the next step.
6. The pilot is located by the main burner and should not re-
quire accessing for lighting.
7.
Turn gas control knob counterclockwise to “PILOT”.
8. Push in gas control knob all the way and hold. Immedi-
ately light the pilot by repeatedly depressing the piezo spark
ignitor until a flame appears. Continue to hold for about
one (1) minute after the pilot is lit. Release gas control knob
and it will pop back. Pilot should remain lit. If it goes out,
repeat steps 5 through 8.
• If gas control knob does not pop up when released, stop
and immediately call your service technician or gas suppier.
• If the pilot will not stay lit after several tries, turn the
gas control knob to “OFF” and call your service techni-
cian or gas supplier.
9. Turn on all electric power to fireplace.
10. Turn gas control knob counterclockwise to “ON”.
11. This valve is equipped with a HI/LO feature. Set fireplace
input as desired.
12. Close lower louver panel.
O
F
F
P
I
L
O
T
O
N
L
O
I
H
Piezo
Ignitor
Gas
Control
Knob
Variable Control Knob
Figure 58 - Control Valve Millivolt
TO TURN OFF GAS
TO APPLIANCE
1. Open lower louver panel.
2. Set the wall switch to the OFF position or the GHRC selector
switch (when equipped) to prevent draining the battery.
3. Turn off all electric power to the appliance if service is to
be performed.
4.
Push in gas control knob slightly and turn clockwise
to “OFF”.
5. Close lower louver panel.
Shutting Off Berners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
1.
Turn gas control knob clockwise to the PILOT position.
2. Set the wall switch to the OFF position or the GHRC selector
switch (when equipped) to prevent draining the battery.
MANUAL LIGHTING
PROCEDURE
1. Remove glass door (see Removing/Replaceing Glass Door,
page 24).
2. Follow steps 1 through 8 under Lighting Instructions.
3. Depress gas control knob and light pilot with match.
4.
Keep gas control knob pressed in for 30 seconds after light-
ing pilot. After 30 seconds, release gas control knob. Fol-
low steps 10 through 14 under Lighting Instructions.
5. Replace glass door (see Removing/Replacing Glass Door,
page 24).
OPTIONAL HAND-HELD
REMOTE OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, page 43). Follow instructions included
with the remote control.
After lighting, let pilot flame burn for about one minute. Turn
control knob to ON position. Adjust flame adjustment knob
anywhere between HI and LO. Slide the selector switch to the
REMOTE position (see Figure 61, page 28).
Note:
The burner
may light if hand-held remote was on when selector switch was
last turned off. You can now turn the burner on and off with the
hand-held remote control unit.
NOTICE: You must light the pilot before using the hand-
held remote control unit. See
Lighting Instructions
.