Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
110112-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
10
INSTALLATION
Relocating Wall Switch Assembly (Cont.)
CAUTION: Be careful of gas lines and wiring when
moving floor.
For Mantel Installation
If fireplace is to be installed into a mantel, (see Conventional
Fireplace Installation, page 15) the wall switch assembly may be
mounted on either side of the mantel, facing to the side. Do not locate
wall switch assembly anywhere on the front face of the mantel.
1. Determine the new location for the wall switch assembly. The
wires attached to switch are six feet long.
2. Remove 2 screws securing plastic wall switch assembly to
bracket in fireplace lower cavity. Save screws.
3. Remove wire tie holding coiled wire attached to wall switch
assembly (see Figure 8).
4. Remove wall switch assembly from bracket.
5. Carefully pass wall switch assembly and cord through large
elongated hole in rear of either left or right floor support bracket,
depending on desired location of switch. Pass wall switch as-
sembly and cord through 1.5" diameter hole in side of fire-
place outer casing (see Figure 9).
6. Pull wall switch assembly and cord from fireplace making sure
wall switch assembly will reach desired mounting location
without straining cord assembly.
If you are mounting wall switch assembly to a wall, continue
reading. If you are mounting your wall switch assembly to the side
of the mantel, see page 11.
INSTALLATION
Continued
Figure 8 - Relocating Wall Switch Assembly
CAUTION: Do not apply excessive pull on cord.
Figure 9 - Routing Wall Switch Assembly Through Fireplace for
Relocation
Wall Switch
Assembly
Wire Tie
Burner
Outlet
Tube
Gas Control Valve
Firebox
Bottom
Wall Switch Assembly
Hole in Outer
Casing
Hole in
Floor
Support
Bracket
Mounting Wall Switch Assembly to Wall for Recessed Fireplace
7. Create three openings on wall according to Template 1, page
33. This is best done by making a pattern to work with on your
wall. Carefully cut page 33/34 from manual and tape paper
template vertically onto wall at preferred location. Pierce the
paper at the centers of the 2 holes with a nail or sharp pencil,
leaving a mark on the wall. Do the same at centers of the four
circles near the corners of the rectangle.
8. Remove paper template from wall.
9. Drill 3/8" holes at each mark.
10. Using a straight edge and pencil, connect the outer edges of
the 4 holes for the rectangle (see Figure 10). This will give you
cutting lines for the rectangle you will cut in the wall.
11. Using a keyhole saw, hack saw blade, drill, file, or other suit-
able tool, carefully cut out the rectangular opening.
Note:
The
corners of the rectangle may be round.
IMPORTANT:
Do not
exceed the size of the rectangle on template.
12. From inside the recessed opening for the fireplace, carefully
pass wall switch assembly through the rectangular opening to
the outside of the wall.
13. Using wall anchors supplied in hardware package, fold wall
anchor as shown in Figure 11.
14. Insert wall anchor, wings first, into hole. Tap anchor flush to wall.
15. For thin walls (1/2" or less), insert red key into wall anchor.
Push red key to “pop” open anchor wings. See Figure 12.
IMPORTANT:
Do not hammer key! For thick walls (over 1/2"
thick), do not pop open wings.
Figure 11 - Folding Anchor
Figure 12 - Popping Open Anchor
Wings for Thin Walls
Figure 10 - Using Template for Wall Switch Assembly Installation
4
3
/
4
"
3
3
/
4
"
3/8"
3/16"
3/4"
3/8" Diameter
2 Holes
Template
from This
Manual
Cutting
Lines
Make Marks
at Centers
of Holes
Tape