Weber PL - PG. 59 57205 Gas Grill User Manual


  Open as PDF
of 84
 
22 WWW.WEBER.COM
®
TROUBLESHOOTING
GENERAL TROUBLESHOOTING
PROBLEMS SOLUTIONS
Burner does not ignite when you push the
igniterbutton.
Besurethatthereisgasowtotheburnersbyattemptingtomatchlightyourburners.Referto“MAINBURNER
IGNITION—LightingwithaMatch.”Ifmatchlightingissuccessful,theproblemliesintheignitionsystem.Referto
“MAINTAININGTHEELECTRONICCROSSOVER
®
IGNITIONSYSTEM.”
Be sure that wires are correctly inserted into terminals on igniter module. Check that the wires are connected to
terminalsonigniterbuttonunderthecontrolpanel.Referto“IGNITERMODULEWIREGUIDE.”
If a new battery is installed, conrm that battery’s plastic wrapping has been removed. Verify that the battery is in good
conditionandhasbeeninstalledcorrectly.Referto“MAINTAININGTHEELECTRONICCROSSOVER
®
IGNITION
SYSTEM.”
Burners do not ignite.
Burners have a small ickering ame when burner
control knobs are in the high (
) position.
Grill temperature only reaches 250° to 300° F in
the high (
) position.
The excess ow safety device, which is part of the grill-to-cylinder connection, may have been activated. To reset the
excessowsafetydevice,referto“MAINBURNERIGNITION.”
m DANGER: When the “excess gas ow control” feature is activated, a small amount of gas is still owing to
the burners. After turning off the LP cylinder valve and burner control knobs, wait at least ve minutes for the
gas to clear before attempting to light the grill. Failure to do so may result in an explosive are-up, which can
cause serious bodily injury or death.
Burner does not ignite, or ame is low in
high (
) position.
LP fuel could be low or empty. Rell LP cylinder.
Fuel hose could be bent or kinked. Straighten fuel hose.
Burner ame pattern is erratic.
Flame is low when burner is on high (
) position.
Flames do not run the whole length of the
burnertube.
Cleanburnerportsthatrundowntheentirelengthofburnertube.Referto“ANNUALMAINTENANCE.”
Burners burn with a yellow or orange ame, in
conjunction with the smell of gas.
Inspect spider/insect screens for possible obstructions. (Blockage of holes.) Clean spider/insect screens.
Referto“ANNUALMAINTENANCE.”
Experiencing are-ups.
m CAUTION: Do not line the slide-out
grease tray with aluminum foil.
Grill must be preheated with all burners on high for 10 to 15 minutes.
Clean the cooking grates and Flavorizer
®
barsthoroughlytoremovegrease.Referto“CLEANINGTHEINSIDEOF
THEGRILL.”
The slide-out grease tray may be dirty and is not allowing grease to ow into catch pan. Clean slide-out grease tray.
Inside of lid appears to be “peeling.”
(Resembles paint peeling.)
Theinsideofthelidisporcelainenamelorstainlesssteel.Itisnotpainted.Itcannot“peel.”Whatyouareseeingis
baked-on grease that has turned to carbon and is aking off. THIS IS NOT A DEFECT. Clean thoroughly. Refer to
“CLEANINGTHEINSIDEOFTHEGRILL.”
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
®
.
SIDE BURNER TROUBLESHOOTING
PROBLEMS SOLUTIONS
Side burner does not ignite when you push the
igniter button.
Besurethatthereisgasowtotheburnerbyattemptingtomatchlightyoursideburner.Referto“SIDEBURNER
IGNITION—LightingwithaMatch.”Ifmatchlightingissuccessful,theproblemliesintheignitionsystem.Referto
“MAINTAININGTHEELECTRONICCROSSOVER
®
IGNITIONSYSTEM.”
Be sure that wires are correctly inserted into terminals on igniter module. Check that the wires are connected to
terminalsonigniterbuttonunderthecontrolpanel.Referto“IGNITERMODULEWIREGUIDE.”
If a new battery is installed, conrm that battery’s plastic wrapping has been removed. Verify that the battery is
ingoodconditionandhasbeeninstalledcorrectly.Referto“MAINTAININGTHEELECTRONICCROSSOVER
®
IGNITIONSYSTEM.”
Side burner does not ignite. Be sure that gas supply is on.
The excess ow safety device, which is part of the grill-to-cylinder connection, may have been activated. To reset the
excessowsafetydevice,referto“MAINBURNERIGNITION.”
m DANGER: When the “excess gas ow control” feature is activated, a small amount of gas is still owing to
the burners. After turning off the LP cylinder valve and burner control knobs, wait at least ve minutes for the
gas to clear before attempting to light the grill. Failure to do so may result in an explosive are-up, which can
cause serious bodily injury or death.
Side burner does not ignite, or ame is low when
burner is on high (
) position.
LP fuel could be low or empty. Rell LP cylinder.
Fuel hose could be bent or kinked. Straighten fuel hose.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
®
.
 previous next