Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
25
106516
OWNER’S MANUAL
O
F
F
P
I
L
O
T
O
N
L
O
I
H
OPERATING
FIREPLACE
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around
the appliance area for gas. Be sure to
smell next to the floor because some gas
is heavier than air and will settle on
the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn by
hand, don't try to repair it, call a quali-
fied service technician. Force or at-
tempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part
of the control system and any gas con-
trol which has been under water.
FOR YOUR SAFETY
READ BEFORE
LIGHTING
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information in
column one.
2. Open lower louver panel.
3. Disconnect the wire that runs from TH
to TPTH from the valve.
4. Turn off all electric power to the
fireplace.
5. Push in gas control knob slightly and
turn clockwise
to “OFF”.
TO TURN OFF GAS
TO APPLIANCE
1. Open lower louver panel.
2a. If Using Optional ON/OFF Switch:
Turn ON/OFF switch to “OFF”.
2b. If Using Optional Hand-Held Re-
mote: Set selector switch in the OFF
position to prevent draining battery.
Figure 56 - Control Valve
Piezo
Ignitor
Gas Control Knob
Variable Control Knob
OPTIONAL REMOTE
OPERATION
Note:
All remote control accessories must
be purchased separately (See Accessories
on pages 34 and 35). Follow instructions
included with the remote control.
Thermostat Control Operation
(Optional GHRCT Only) The thermostat
control setting on the remote control unit
can be set to any comfort level between HI
and LO. The burners will turn on and off
automatically to maintain the comfort level
you select. The ideal comfort setting will
vary by household depending upon the
amount of space to be heated, the output of
the central heating system, etc.
NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See
Lighting
Instructions
.
6. Wait five (5) minutes to clear out any
gas. Then smell for gas, including near
the floor. If you smell gas, STOP! Fol-
low “B” in the safety information in
column one. If you don't smell gas, go
to the next step.
7. The pilot is located by the main burner
and should not require accessing for
lighting.
8. Turn gas control knob counterclock-
wise
to “PILOT”.
9. Push in gas control knob all the way and
hold. Immediately light the pilot by re-
peatedly depressing the piezo spark ig-
nitor until a flame appears. Continue to
hold for about one (1) minute after the
pilot is lit. Release gas control knob and
it will pop back. Pilot should remain lit.
If it goes out, repeat steps 5 through 8.
• If gas control knob does not pop up when
released, stop and immediately call your
service technician or gas supplier.
• If the pilot will not stay lit after sev-
eral tries, turn the gas control knob
to “OFF” and call your service tech-
nician or gas supplier.
10. Reconnect the wire that runs from TH
to TPTH from the valve.
11. Turn on all electric power to the
fireplace.
12. Turn gas control knob counterclock-
wise
to “ON”.
13. This valve is equipped with a HI/LO
feature. Set fireplace input as desired.
14. Close lower louver panel.
3. Turn off all electrical power to the ap-
pliance if service is to be performed.
4. Push in gas control knob slightly and
turn clockwise
to “OFF”.
5. Close lower louver panel.
Shutting Off Burners Only (pilot
stays lit)
You may shut off the burners and keep the
pilot lit by doing one of the following:
1. Turn gas control knob clockwise
to the PILOT position.
2. Set selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
1. Remove glass door (see Removing/Re-
placing Glass Door, page 22).
2. Follow steps 1 through 8 under Light-
ing Instructions.
3. Depress gas control knob and light pi-
lot with match.
4. Keep gas control knob pressed in for 30
seconds after lighting pilot. After 30 sec-
onds, release gas control knob. Now fol-
low steps 10 through 14, column 2.
5. Replace glass door (see Removing/Re-
placing Glass Door, page 22).
Continued