Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
110150-01B
For more information, visit www.desatech.com
For more information, visit www.desatech.com
7
7
INSTALLATION
CAUTION: This fireplace insert creates warm air
currents. These currents move heat to wall surfaces
next to fireplace insert. Installing fireplace insert next
to vinyl or cloth wall coverings or operating fireplace
insert where impurities (such as, but not limited to,
tobacco smoke, aromatic candles, cleaning fluids, oil
or kerosene lamps, etc.) in the air exist, may discolor
walls or cause odors.
WARNING: A qualified service person must in-
stall fireplace insert. Follow all local codes.
WARNING: Never install the fireplace insert
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture, clothing, or other flam-
mable objects are less than 42 inches from the
front, top, or sides of the fireplace insert
• in high traffic areas
• in windy or drafty areas
NOTICE: This heater is intended for use as supple-
mental heat. Use this heater along with your primary
heating system. Do not install this heater as your
primary heat source. If you have a central heating
system, you may run system’s circulating blower
while using heater. This will help circulate the heat
throughout the house. In the event of a power outage,
you can use this heater as your primary heat source.
WARNING: Before installing in a solid fuel burn-
ing fireplace, the chimney flue and firebox must be
cleaned of soot, creosote, ashes, and loose paint by
a qualified chimney cleaner.
Note:
Your Vanguard fireplace insert is designed to be used in zero
clearance installations. Wall or framing material can be placed
directly against any exterior surface on the rear, sides, or top of your
fireplace insert, except where standoff spacers are integrally at-
tached. If standoff spacers are attached to your insert, these spacers
can be placed directly against wall or framing materials.
IMPORTANT:
Vent-free heaters add moisture to the air. Although
this is beneficial, installing fireplace in rooms without enough
ventilation air may cause mildew to form from too much moisture.
See Air for Combustion and Ventilation, pages 4 through 6.
IMPORTANT:
Make sure the fireplace insert is level. If fireplace
insert is not level, log set will not work properly.
CAUTION: Close masonry fireplace damper se-
curely before installing fireplace insert. If chimney
does not have a damper, block or cap top of chimney.
Failure to cap an open chimney could cause drafts
that can affect the heater’s performance and increase
surface temperatures.
INSTALLING SURROUND KIT (GS38 OR GS43)
CAUTION: If using a GS38 or GS43 surround kit
accessory, it must be installed on this fireplace insert
before installing into your masonry fireplace or wall
opening.
CHECK GAS TYPE
Use the correct gas type (natural or propane/LP) for your unit. If your
gas supply is not correct, do not install fireplace insert. Call dealer
where you bought fireplace insert for proper type fireplace insert.
ELECTRICAL HOOKUP
(Blower Accessory)
This fireplace insert includes a blower assembly with an electrical
cord. The electrical cord is five feet in length. You must locate
fireplace insert within reach of a 120 volt grounded electrical outlet.
If not, install and properly ground GA3555, three-prong 120 volt
electrical outlet, in fireplace insert. Follow instructions included in
kit (see Accessories, page 30).
Note:
Use the accessory which best covers the existing masonry
fireplace opening or wall opening.
• Model GS38 Surround Kit (for use with fireplaces with an open-
ing smaller than 30" H and 38" W)
• Model GS43 Surround Kit (for use with fireplaces with an open-
ing 30" to 36
3
/
4
" H and 38" to 43" W)
1. Using a 5/16" nut driver, remove two shoulder screws and
screen (see Figure 5). Remove 5/16" screen mounting shoul-
der screws (do not discard).
INSTALLATION
Check Gas Type
Electrical Hookup
Installing Surround Kit (GS38 or GS43)
Shoulder
Screw
Screen
Mounting
Shoulder
Screw (4)
Figure 5 - Removing Screws and Screen