Vanguard VI33PRA Fire Pit User Manual


 
110150-01B
For more information, visit www.desatech.com
For more information, visit www.desatech.com
17
17
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the remote
selector switch to the REMOTE position (see Figure 34).
Note:
The burners may light if hand-held remote ON but-
ton was on when remote selector switch was last turned
off. You can now turn the burners on and off with the hand-
held remote control unit.
IMPORTANT
: Do not leave the remote selector switch in
the REMOTE position when the pilot is not lit. This will
drain the battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burner on and off.
When turning burner off, the pilot will remain lit.
GHRCTA Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 35). The lights to the left of the button
will show AUTO, ON, or OFF.
In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions
on pages 15 and 16.
OPTIONAL REMOTE
OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, page 30). Follow instructions included
with the remote control.
Thermostat Control Operation
(Optional GHRCTA Series Only) The thermostat control set-
ting on the remote control unit can be set to any comfort level
between WARMER and COOLER. The burners will turn on
and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending
upon the amount of space to be heated, the output of the central
heating system, etc.
For wall thermostat operation, follow instruction supplied with
thermostat accessory GWMT1. For wall switch operation fol-
low instructions supplied with GWMS2.
OPERATING FIREPLACE
INSERT
Continued
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
Figure 34 - Setting the Remote Selector Switch, Control Knob,
and Flame Adjustment Knob for Remote Operation
Remote Selector Switch in Remote
Position (Optional Remote Control)
Control Knob in
On Position
Flame Adjustment Knob
Figure 35 - Thermostat Hand-Held Remote Control Unit Selections
(GHRCTA Series only)
Shows Temperature
Setting
Increases Room
Temperature in
AUTO Mode
Decreases Room
Temperature in
AUTO Mode
Turns Burner On or
Off and Allows You
to Choose the Auto
Setting
The Log Heater will
Automatically Cycle
between Pilot and
the Heat Setting that
has been Selected
In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
IMPORTANT:
This remote control has been specially en-
gineered to take an air temperature sample every 5.5 min-
utes in the auto mode. It will not respond immediately to
the temperature setting being turned up or down.
IMPORTANT:
The hand-held remote control unit must
be near the heater. Do not keep the hand-held remote
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the heater off.
3. To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT:
To turn the pilot off, manually turn the con-
trol knob on the heater to the OFF position.
OPERATING FIREPLACE INSERT
Optional Remote Operation