Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
9
W415-0369 / E / 02.16.07
Do not use steel wool, as it will scratch the fi nish. Stainless
steel parts will discolour when heated, usually to a golden or
brown colour. This discolouration is normal and will not affect
the performance of the appliance.
Air shutter adjustment must only be done by a quali-
fi ed gas installer!
When lighting and re-lighting, the gas knob cannot be turned
from pilot to off unless the knob is depressed.
1. Stop! Read the safety information on the operating label.
2. Turn the gas knob clockwise to off.
3. Wait fi ve (5) minutes to clear out any gas. If you smell gas
including near the fl oor, stop! Follow “b” on the operating label.
If you don’t smell gas go to the next step.
4. If fi replace is equipped with fl ame adjustment valve turn
clockwise to off.
5. Find pilot located in front of back log.
6. Turn gas knob counter-clockwise to pilot.
7. Depress and hold gas knob while lighting the pilot with the
push button igniter. Keep knob fully depressed for one minute,
then release. If pilot does not continue to burn repeat steps 3
through 7.
8. With pilot lit, turn gas knob counter-clockwise to
on.
9. If equipped with fl ame adjustment valve, push and turn knob
to high.
10. If equipped with remote on-off switch, main burner may not
come on when you turn the valve to on or high. Remote switch
must be in the on position to ignite burner.
Closing the air shutter will cause a more yellow fl ame, but
can lead to carboning. Opening the air shutter will cause a
more blue fl ame, but can cause fl ame lifting from the burner
ports. The fl ame may not appear yellow immediately; allow
15 to 30 minutes for the fi nal fl ame colour to be established.
Opening the air shutter will also reduce exhaust odours. See
Trouble Shooting Guide.
CAUTION: Label all wires prior to disconnection when servic-
ing controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing. This heater
should be inspected and serviced before use and at least an-
nually by a qualifi ed service person. The fi replace area must
be kept clear and free of combustible materials, gasoline or
other fl ammable vapours and liquids. The fl ow of combustion
and ventilation air must not be obstructed.
2. Keep the control compartment, logs, burner, air shutter
opening and the area surrounding the logs clean by vacuum-
ing or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out
any of the ports which may not be burning or are not burn-
ing properly.
4. Check to see that the pilot fl ame is large enough to engulf
the thermocouple and thermopile and promptly ignites the
main burner.
6. Check to see that the main burner ignites completely on all
openings when the gas knob for the burner is turned on. A 5 to
10 second total light-up period is satisfactory. If ignition takes
longer, consult your NAPOLEON® dealer / distributor.
Cleaning Stainless Steel: Do not use abrasive cleaners to
clean any painted, porcelain or stainless steel parts. To clean
stainless surfaces, use a stainless steel cleaner or a non-
abrasive cleaner. Always wipe in the direction of the grain.
FIGURE 16
MAINTENANCE
VENTURI ADJUSTMENT
If heater keeps shutting off, have it serviced. Keep burner
and control compartment clean.
When lit for the fi rst time, the fi replace will emit a slight
odour for a few hours. This is a normal temporary condi-
tion caused by the curing of the logs and the “burn-in” of
internal paints and lubricants used in the manufacturing
process and will not occur again.
After extended periods of non-operation such as follow-
ing a vacation or a warm weather season, the fi replace
may emit a slight odour for a few hours. This is caused
by dust particles burning off.
OPERATION / MAINTENANCE
• Do not use a mobile or land phone.
• If you cannot reach your gas supplier, call the fi re department.
• Turn off all gas to the fi replace.
• Do not try to light any appliance.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s instructions.
A. This fi replace is equipped with a pilot which must be lit by hand
while following these instructions exactly.
B. Before operating smell all around the fi replace area for gas
and next to the fl oor because some gas is heavier than air and
will settle on the fl oor.
C. Use only your hand to turn the gas control knob / manual
shut-off knob. Never use tools. If the knob will not turn by hand,
do not try to repair it. Call a qualifi ed service technician. Force or
attempted repair may result in a fi re or explosion.
D. Do not use this fi replace if any part has been under water. Im-
mediately call a qualifi ed service technician to inspect the fi replace
and replace any part of the control system and any gas control
which has been under water.
• Push in gas control knob slightly and turn clockwise to
off. Do not force.
FOR YOUR SAFETY READ BEFORE LIGHT-
WHAT TO DO IF YOU SMELL GAS
LIGHTING INSTRUCTIONS
TO TURN OFF GAS
NG 3/16”
LP 1/4”
AIR SHUTTER
OPENINGS