Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
3) Match light the burner
through the opening
between Grill Body and
the Cooking Surface.
9
Lighting the Grill Using the Igniter
· Open Hood before lighting the grill to prevent an
explosion from gas build-up.
· Always inspect the gas hose and regulator assembly
before each use. If the hose is cut, damaged, or
shows signs of excessive abrasion or wear, do not
use the LP gas grill. Contact the manufacturer, as the
hose and regulator assembly must be replaced with
an assembly specified by the manufacturer prior to
further use of the LP gas grill.
3) Push in Control Knob; turn
counterclockwise to the “I”
position until you feel resistance.
FIG. 20B
4) Check through the opening
between grill body and the
Cooking Surface to see if
burner is lit.
FIG. 20C
· Open Hood before lighting the grill to prevent an
explosion from gas build-up.
· Always inspect the gas hose and regulator assembly
before each use. If the hose is cut, damaged, or
shows signs of excessive abrasion or wear, do not
use the LP gas grill. Contact the manufacturer, as the
hose and regulator assembly must be replaced with
an assembly specified by the manufacturer prior to
further use of the LP gas
Manual Lighting of the Grill
How to manually light your LP
gas grill
1) Open the Hood. Make sure LP Cylinder is connected and
Control Knobs are “Off”.
2) If using a 20 lb. LP Cylinder instead of 1 lb LP Cylinder,
open the LP Cylinder valve by turning the valve handle
counter-clockwise until it stops. (SEE FIG. 20A)
3) From the “OFF” position, push in and turn the Control
Knob counterclockwise to “H”. (FIG. 21A)
4) Match light the burner with the supplied match holder
and a match near the burner. (FIG. 21B & Fig. 21C)
WARNING: Keep your face away from the opening.
5) If burner does not light, turn Control Knob to “OFF”.
Close the valve on the 20 lb. LP gas cylinder.
Remove the Cooking Surfaces to dissipate the gas. Wait
five minutes then repeat Steps 2 and 3.
6) If burner still fails to light, wait five minutes and refer to
the T
roubleshooting page.
7) After ignition, preheat the Grill and Cooking Surface by
turning the Control Knob to “High” for about 8 minutes.
WARNING: If the burner goes out while cooking,
turn the Control Knob to the “OFF” position. Wait five
minutes before attempting to relight the grill.
2) Push in Control Knob; turn counter-
clockwise to the “H” position.
FIG. 21A
FIG. 21B
FIG. 21C
How to light your LP gas grill using the ignitor
1) Open the Hood. Make sure LP Cylinder is connected and
Control Knobs are “Off”.
2) If using a 20 lb. LP Cylinder instead of 1 lb LP Cylinder,
open the LP gas cylinder valve by turning the valve
handle counter-clockwise until it stops. (FIG. 20A)
3) From the “OFF” position, push in and turn the Control
Knob counterclockwise to “I” when you feel resistance.
(FIG. 20B)
4) Pause 4 seconds, then push in and turn the Control
Knob until a click is heard and the burner is lit. Check
through the grill body opening and the Cooking Surface
to see if burner is lit. (FIG. 20C)
5) Repeat Step 3 until burner is lit.
6) If burner does not light or ignitor does not work, turn
Control Knob to “OFF”. Close the valve on the 20 lb.
LP gas cylinder. Remove the Cooking Surfaces to
dissipate the gas. Wait five minutes, then repeat Steps 2
thru 4.
7) If burner still fails to light, repeat step 5, wait five
minutes and refer to the T
roubleshooting page. If it fails
to light, the burner can be lit manually, see Manual
Lighting of the Grill
.
8) After ignition, preheat the Grill and Cooling Surface by
turning the Control Knob to “High” for about 8 minutes.
WARNING: If the burner goes out while cooking,
turn the Control Knob to the “OFF” position. Wait five
minutes before attempting to relight the grill.
2) Turn 20 lb. LP Cylinder
handle counter-clockwise
“ON”.
FIG. 20A
1) Turn 20 lb. LP Cylinder handle
counter-clockwise “ON”. (See FIG. 20A)
Manual Lighting proximity
with Cooking Surfaces
removed.