Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
105706-01B
For more information, visit www.desatech.com
For more information, visit www.desatech.com
23
23
TO TURN OFF GAS
TO APPLIANCE
1. Turn off the wall switch.
2. Turn off all electric power to the appliance if service is to
be performed.
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information in column 2, page 22,
before proceeding.
2. Set the “HI-LO” knob to the lowest setting.
3. Turn off all electrical power to the appliance.
4. Open control access panel.
5. Push in gas control knob slightly and turn clockwise
to “OFF”.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information in column 2, page 22. If
you don’t smell gas, go to the next step.
7. The pilot is located by the main burner.
8. Turn knob on gas control counterclockwise to
“PILOT”.
9. Push in the control knob all the way and hold in. Immedi-
ately light the pilot by pressing the ignitor button until a
flame appears one (1) minute after the pilot is lit. Release
knob and it will pop back up. Pilot should remain lit. If it
goes out, repeat steps 5 through 9.
• If knob does not pop out when released, stop and call gas
supplier.
• If the pilot will not stay lit after several tries, turn gas
control knob to “OFF” and call your service technician
or gas supplier.
10. Turn gas control knob counterclockwise to “ON”.
Knob can be turned to “ON” only if the control knob is
popped out.
11. Set “HI-LO” knob to desired setting.
12. Turn on all electric power to the appliance.
Figure 50 - Control Knob in the PILOT Position
O
F
F
P
I
L
O
T
O
N
L
O
H
I
P
I
L
O
T
EA
16AI
7
TPTH TP TH
Position Indicator
Gas Control Knob
OPTIONAL REMOTE
OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, page 29). Follow instructions included
with the remote control.
HI/LO Knob
OPERATING FIREPLACE
Lighting Instructions
To Turn Off Gas To Appliance
Optional Remote Operation
OPERATING FIREPLACE
Continued
Figure 51 - Pilot
Thermocouple
Pilot Burner
Piezo Ignitor
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions
, page 22.
Thermopile
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position.
Note:
The burners may light if
hand-held remote ON button was on when selector switch
was last turned off. You can now turn the burners on and off
with the hand-held remote control unit.
IMPORTANT:
Do not leave the selector switch in the RE-
MOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
2. Press ON/OFF button to turn the burners on and off. When
turning burners off, the pilot will remain lit.
Figure 52 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
ON
OFF
REMOTE
O
F
F
P
I
L
O
T
O
N
L
O
I
H
Selector Switch in Remote Position
(Optional Remote Control)
Control Knob in On Position
Flame Adjustment Knob
3. Remove control access panel.
4. Push in gas control knob slightly and turn clockwise
to “OFF”. Do not force.
5. Replace control access panel.