Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
BasicLighting Procedures
Machine oils used in the manufacturing processof
stainless steel can cause stainless steel to turn a tan
color Before initialgrill use, remove protective PVC
film from Control Panel and inside and outside of Grill
Lid. Use a Stainless Steel Cleaner to polish the
stainless steel and remove these excess oils from
yourgrilt. Never use abrasive cleaners orscrubbers
because they wilt scratch and damage your grill. For
details, see Cleaning Exterior Stainless Steel
Surfaces on page 18.
Gas Lighting Instructions
Familiarize yourself with the safety guidelines at the
front of this manual. Do not smoke while lighting grill or
checking gas supply connections.
1. If you have a LP gas grill be sure the LP gas tank
is filled, or if you have a NG grill be sure that the
locking shut off vatve isopen.
2. Check thatthe end of each Burner Tube is properly
located over each Valve Orifice.
3. Be sure all gas connections are securely tightened.
4. Open the Gritl Lid or Side Burner Lid, depending
on the Burner you are lighting.
WARNING
Failure to open Grill Lid during the
lighting procedures could result in a fire
or explosion that could cause serious
bodily injury, death, or property damage.
5. Set ALL Control Knobs to OFF, and for LP Models,
open gas tank valve slowly until 1/4 to 1/2 open.
Open LP
gas tank
|
OFF ""
6. Push and turn the LEFT ControI Knob to HIGH.
|
HIGH
OFF I
7. Immediately press the Electric Ignitor for 3-4
seconds to light the Burner.
"\- PRESS
8_
9.
If the burner does not light, turn the Control Knob
to OFF, wait 5 minutes for gas to clear, then retry.
Once the left grill burner is ignited, the adjacent
burner can be lit by simply turning its Control Knob
toHIGH.
10. Adjust ControI Knobstoyourdesiredcooking
temperature.
Side Burner Lighting Instructions
1. Follow steps 1 through 5 of the Gas Lighting
Instructions.
2. Push and turn the control knob for Side Burner to
HIGH.
|
HIGH
OFF I ,
@ @ @o@
RIGHT ELECTRIC
IGNITOR
(for SIDE BURNER)
"\
\
\ FUEL GAUGE
x
\ DISPLAY
\
\
SiDE BURNER
3. Immediately press theelectric ignitorfor 3-4
seconds to light the burner.
4. If the burner does not light, turn the control knob to
OFF, wait 5 minutes for gas to clear, then retry.
5. Adjust control knobs to yourdesired cooking
temperature.
Back Burner Lighting Instructions
Note: The location of the Back Burner makes it more
susceptible to winds that will decrease the perfor-
mance of your rotisserie cooking. For this reason you
should not operate the Back Burner during windy
weather conditions.
1. Follow steps 1 through5 of the Gas Lighting
Instructions.
2. Open the Grill Lid. Failure todo so can result in
fire or explosion. SeeWARNING left.
.
4.
5.
6.
7.
8_
16
Set ALL Control Knobs to OFF and open the LP
gas tank valve slowly until 1/4 to 1/2 open.
Push and turn the Right Control Knob for Back
Burner to HIGH.
Then immediately press the Electric Ignitor for
3-4 seconds to light the Back Burner.
If the Burner does not light turn the Control Knob
to OFF, wait 5 minutes for gas to clear, then retry.
Once lit, the Back Burner witl reach cooking
ternperature quickly. The orange/red glowwitl even
out in about 5 minutes.
For best results, always rotisserie cook with the
grill Lid down and the Back Burner Contret Knob
setto HIGH. Do not use the main grill Burners
when the Back Burner is in operation.