Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
7
107497
OWNER’S MANUAL
For more information, visit www.desatech.com
Figure 7 - Checking Gas Joints
SETUP
Your Comfort Glow Patio Fire is designed
to operate with lava rock piled in and around
the burner, and refractory logs placed on top
of the lava rock.
Carefully pour supplied lava rock into basin
to cover the burner. Be sure that the burner
and burner ports are covered completely by
lava rock to better disperse the flame and to
create a more natural looking fire.
Place the six refractory logs on top of the
lava rock. The arrangement is left to your
personal preference. Try different place-
ments to achieve your desired flame pattern.
Note:
Sooting on the logs is natural. You
may clean with a soft bristle brush.
CAUTION: Place lava rock
carefully. Be careful not to dam-
age the burner, ignitor electrode,
or thermocouple when adding the
lava rock.
WARNING: Allow logs and
lava rock to cool completely be-
fore handling or rearranging logs.
WARNING: Solid fuels shall
not be burned in this gas fireplace.
INSTALLATION
(Continued)
2. Pressurize supply piping system by ei-
ther using compressed air or opening
propane/LP supply tank valve.
3. Check all joints from propane/LP sup-
ply tank to equipment shutoff valve (see
Figure 7). Apply mixture of liquid soap
and water to gas joints. Bubbles form-
ing show a leak.
4. Correct all leaks at once.
Pressure Testing Appliance Gas
Connections (Fixed Piping
System Only)
1. Open equipment shutoff valve (see Fig-
ure 6, page 6).
2. Open propane/LP supply tank valve.
3. Check all joints from equipment shutoff
valve to supply hose. Apply mixture of
liquid soap and water to gas joints.
Bubbles forming show a leak.
4. Correct all leaks at once.
BATTERY INSTALLATION
Your Comfort Glow Patio Fire uses an elec-
tronic ignitor which requires one AA alka-
line battery (not included). The battery com-
partment is located in the ignitor module
behind the ignitor button.
To install the battery into the ignitor:
1. Locate the ignitor button on the con-
trol panel (see Figure 8).
2. Rotate the ignitor button counterclock-
wise to remove.
3. Install a fresh AA alkaline battery into
the ignitor module, positive terminal first.
4. Replace button by rotating clockwise.
Tighten finger tight. Do not over-
tighten.
Note:
Your fire pit may be lighted using a
match (see Lighting Instructions, page 8).
Ignitor Button
Figure 8 - Control Panel
Propane/LP Supply Tank
(100 lb. or larger)
Equipment
Shutoff
Valve
Control Valve
Location
OPERATING
APPLIANCE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury, or loss of life.
BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell next
to the ground because some gas is heavier
than air and will settle on the ground.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
WARNING: Do not use this
appliance if any gas control parts
have been under water. Immedi-
ately call a qualified service per-
son to inspect the Patio Fire and
replace any part of the control
system and any gas control that
has been under water.
WARNING: All gas burning
appliances may produce smoke,
soot, or carbon monoxide during
operation. These fumes can be
harmful if the appliance is used
anywhere other than in an open
air, fully-vented area.
Continued