Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
E-3
Step 1.
On a flat surface (table or carport floor), OPEN AND EMPTY BOTH
BOXES.REFER TO THE CONTENTS LIST TO BE SURE NO PARTS
ARE MISSING.Tighten all factory installed fasteners that may have
loosened during shipping.
Step 2.
Refer to Figure 2. Select the following parts for assembly:
1. cabinet side panels (2 ea) 4. tank support brackets (2 ea)
2. lower valance (2 ea) 5. magnetic door catch (1ea)
3. casters (4 ea)
Attach magnetic catch to right cabinet side panel as shown in Figure
2a using 2 each 8-32 x 3/8 Phillips screws, nuts and lock washers.
Bolt the lower valance (2 ea) to the bottom front/rear of the cabinet side
panels using the 1/4-20 x 5/8” hex head bolts and lock washers as
shown in Figure 2b. Do not fully tighten them at this time.
Select the tank supports. Place the tank supports inside the cabinet
and attach them to the backside of the lower valance as shown in
Figure 2B.NOTE:They will attach toward the left side of the cabinet. Be
sure the notches in the tank support bracket are up. Secure with 1/4-20
x 5/8” hex head bolts and lock washers. Check to make sure that the
cabinet is square by measuring diagonally, before tightening any bolts.
NOTE: Cabinet must be held square in order for the door to open and
close properly.Tighten tank support bolts completely.Now go back and
tighten lower valance bolts completely.
Place one each 3/8” flat washer onto the caster stud. Now screw caster
into the lower valance corners.Tighten securely.Repeat for other 3
corners. NOTE: Locking casters go on the front.Lock the casters to
prevent cabinet from moving around during assembly.
ASSEMBLY INSTRUCTIONS
FIGURE 3
FIGURE 2b
#8-32 x 3/8” Round Head Phillips
#10-24x1” Carriage Bolt
#10-24 Hex Nut
1/4 - 20 x 5/8” , 1/4 - 20 x 1”Hex Head Bolt
1/4” Lock washer 1/4” Hex nut
#10 Lock washer
Note: Use one lock washer per bolt, either under the hex nut or under
the bolt head if a hex nut is not used.
FIGURE 2a
#10-24x1/2” Carriage Bolt
#8-32 Hex Nut#8-32 Lock Washer
1/4 - 20 x 1” Round Head Phillips
#10-24 x 3/8”, #10-24 x 1/2” Round Head Phillips
1/4-20 x 1/2” Wing Bolt
(For Tank Hold Down Bracket)
Fasteners Guide
❍
❍
❍
❍
❍
Insert and fasten Bucket
Bracket into slot as shown
10-24 Phillips head screw
and lock washer
Loosen these 2 bolts.
DO NOT REMOVE COMPLETELY
Electrode
8-32 Phillips head screw
and lock washer
Cabinet side, RIGHT
8-32 x 3/8 Screw
8-32 x 3/8 Hex Nut and Lock Washer
Magnetic Catch
Cabinet side, RIGHT
Lower Valance
Tank Support
1/4 - 20 Hex Bolt and
Lock Washer
(typ 8 plcs)
Lower Valance
Tank Notches
1/4 - 20 Hex Bolt and
Lock Washer
(typ 4 plcs)
3/8” Flat Washer
Heavy Duty Caster
Cabinet side, LEFT
#10-24 “Top Lock” Hex Nut