Special offers from our partners!
![Sponsored Listings Image](http://mostatic.manualsonline.com/static/img/listings/applfactpart.png)
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
![](http://pdfasset.owneriq.net/c/a9/ca9db746-a575-46fe-b6c2-b558367c8085/ca9db746-a575-46fe-b6c2-b558367c8085-bg1d.png)
Part # 4526884 Rev 4 (10/08/10) Page 29
PROGRAMMING continued
8. Press
to return to “PROGRAMMING MODE SYSTEM
SETUP”
9. Press
again to exit.
To Change the Alarm Volume:
1. Press and hold for three, (3) seconds. “ENTER CODE” is
displayed.
2. Using the Product buttons, 0-9
enter the code, (1251).
“ENTER CODE **** ” is displayed.
3. Press
to enter the Programming Mode.
“PROGRAMMING MODE MENU ITEMS” is displayed.
4. Press
two, (2) times. “PROGRAMMING MODE SYSTEM
SETUP” is displayed.
5.
Press
three, (3), times. “ALARM VOLUME LOW (or
HIGH)” is displayed.
6. Use or
to change the Alarm Volume to either Low
or High.
7. Press
to save the changes.
8. Press
to return to “PROGRAMMING MODE SYSTEM
SETUP”
9. Press
again to exit.
To Change the Key Chirp:
To turn key chirp on or o in programing mode only.
1. Press and hold for three, (3) seconds. “ENTER CODE” is
displayed.
2. Using the Product buttons, 0-9
enter the code, (1251).
“ENTER CODE **** ” is displayed.
3. Press
to enter the Programming Mode.
“PROGRAMMING MODE MENU ITEMS” is displayed.
4. Press
two, (2) times. “PROGRAMMING MODE SYSTEM
SETUP” is displayed.
5.
Press
four, (4), times. “KEY CHIRP ON (or OFF” is
displayed.
6. Use or
to change the key chirp to either ON or OFF.
7. Press
to save the changes.
8. Press
to return to “PROGRAMMING MODE SYSTEM
SETUP”
9. Press
again to exit.
To Change Probe Calibration - Upper:
1. Press and hold for three, (3) seconds. “ENTER CODE” is
displayed.
2. Using the Product buttons, 0-9
enter the code, (1251).
“ENTER CODE **** ” is displayed.
3. Press
to enter the Programming Mode.
“PROGRAMMING MODE MENU ITEMS” is displayed.
4. Press
two, (2) times. “PROGRAMMING MODE SYSTEM
SETUP” is displayed.
5.
Press
five, (5), times.
“PROBE CAL – UPPER XXXF” is
displayed.
6. Use or
to change the Probe Calibration to the
correct temperature measured with a pyrometer.* SEE
CALIBRATION REQUIREMENTS and CALIBRATION section.
7. Press
to save the changes.
8. Press
to return to “PROGRAMMING MODE SYSTEM
SETUP”
9. Press
again to exit.
To Change Probe Calibration - Grill:
1. Press and hold for three, (3) seconds. “ENTER CODE” is
displayed.
2. Using the Product buttons, 0-9
enter the code, (1251).
“ENTER CODE **** ” is displayed.
3. Press
to enter the Programming Mode.
“PROGRAMMING MODE MENU ITEMS” is displayed.
4. Press
two, (2) times. “PROGRAMMING MODE SYSTEM
SETUP” is displayed.
5.
Press
six, (6), times. “PROBE CAL – GRILL XXXF” is
displayed.
6. Use or
to change the Probe Calibration to the
correct temperature measured with a pyrometer.* SEE
CALIBRATION REQUIREMENTS and CALIBRATION Section.
7. Press
to save the changes.
8. Press
to return to “PROGRAMMING MODE SYSTEM
SETUP”
9. Press
again to exit.
*CALIBRATION REQUIREMENTS
The control software will beep to the user when it is
appropriate to calibrate. The control will allow calibration
provided the following conditions are met: