Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
Buy Weber Grill Parts. It couldn't be easier. Find your Weber parts here.
15
WWW.WEBER.COM
®
15
ƽ DANGER
When the “excess gas flow control” feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the barbecue. Failure to do so may result in an explosive
flame-up, which can cause serious bodily injury or death.
3) Turn the cylinder on by turning the cylinder valve counterclockwise.
4) Insert match holder with lit match into the matchlight hole in the front of the
cooking box.
ƽ WARNING: Do not lean over open barbecue. Keep your face
and body at least one foot away from the matchlight hole
when lighting the barbecue.
5) Push BURNER 1 control knob down and turn to START/HI.
6) Check that the burner is lit by looking through the matchlight hole on the front of
the cooking box. You should see a flame.
ƽ WARNING: If the burner does not light in five seconds, turn
the Burner 1 control knob to OFF and wait 5 minutes to let
the gas clear before you try again.
7) After BURNER 1 is lit you can turn on BURNER 2 (and BURNER 3).
Note - Always light BURNER 1 first. The other burners ignite from BURNER 1.
TO EXTINGUISH
Push down and turn each burner control knob clockwise to the OFF position. Turn gas
supply OFF at the source.
OPERATING INSTRUCTIONS
1
5
7
2
6
4
3
* The grill illustrated may have
slight differences than the
model purchased.
MAIN BURNER MANUAL LIGHTING
2
1
5
APAGADO
OFF
ARRETE
PROBLEM CHECK CURE
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas.
Inspect Spider/Insect Screens for possible obstructions.
(Blockage of holes.)
Clean Spider/Insect Screens. (See Section “Annual
Maintenance”)
Symptoms:
Burners do not light. -or- Burners have a small
flickering flame in the “HI” position. -or-
Barbecue temperature only reaches 250˚ to 300˚
in the “HI” position.
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated.
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve off. Disconnect the regulator
from the cylinder. Turn burner control knobs to “HI”. Wait at
least 1 minute. Turn burner control knobs to “OFF”. Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly.
Refer to “Lighting Instructions”.
Burner does not light, or flame is low in “HI”
position.
Is LP fuel low or empty? Refill LP cylinder.
Is fuel hose bent or kinked? Straighten fuel hose.
Does Burner 1 light with a match? If you can light Burner 1 with a match, then check the
Crossover
®
ignition system.
Experiencing flare-ups:
ƽ CAUTION: Do not line the bottom tray
with aluminum foil.
Are you preheating barbecue in the prescribed manner? All burners on HI for 10 to 15 minutes for preheating.
Are the cooking grates and Flavorizer
®
bars heavily
coated with burned-on grease?
Clean thoroughly. (See Section “Cleaning”)
Is the bottom tray “dirty” and not allowing grease to flow
into catch pan?
Clean bottom tray.
Burner flame pattern is erratic. Flame is low when
burner is on “HI”. Flames do not run the whole
length of the burner tube.
Are burners clean? Clean burners. (See Section “Maintenance”.)
Inside of lid appears to be “peeling.” (Resembles
paint peeling.)
The lid is porcelain enamel or stainless steel, not paint.
It cannot “peel”. What you are seeing is baked on grease
that has turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
Clean thoroughly. (See Section “Cleaning”.)
Cabinet doors are not aligned. Check the adjustment pin on the bottom of each door. Loosen adjustment nut/s. Slide door/s until aligned. Tighten
nut.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com
®
.
TROUBLESHOOTING