Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
19
c). If the remote LP cylinder enclosure has four sides, a top and a bottom,
and is intended for installation in a built-in “island” enclosure;
1). At least one ventilation opening (a hole or group of holes, for the
purpose of ventilation) needs to be on one side of the enclosure
that communicates with the outside of the “island” structure. If a gas
leak should occur or the LP cylinder should vent in the LP cylinder
enclosure, the gas should not be allowed to vent or migrate into the
empty or “hollow” area of the “island”. Ventilation openings should
only communicate with the outside of the “island” structure, so that
the gas can dissipate outside of the “island” structure. The ventilation
opening should be located within 5 inches (127mm) of the top of the
enclosure, and should have a total free area of 20 square inches. (This
relates to 1 square inch of ventilation area, per pound of stored fuel).
2). At least one ventilation opening (a hole or group of holes, for the
purpose of ventilation) needs to be on one side of the enclosure that
communicates with the outside of the “island” structure, at the bottom.
If a gas leak should occur or the LP cylinder should vent in the LP
cylinder enclosure, the gas should not be allowed to vent or migrate
into the empty or “hollow” area of the “island”. Ventilation openings
should only communicate with the outside of the “island” structure,
so that the gas can dissipate outside of the “island” structure. The
ventilation opening should be located within 5 inches (127mm) of
the bottom of the enclosure, and should have a total free area of 10
square inches. (This relates to 1/4 square inch of ventilation area, per
pound of stored fuel).
3). The minimum size of the ventilation hole (s) should not be less than
1/4 inch.
d). The remote LP cylinder enclosure should be constructed with non-
combustible materials. The remote LP cylinder enclosure should isolate
the LP cylinder from the burner compartment, so that it provides shielding
from radiation, be a fl ame barrier and provide protection from foreign
material such as hot drippings.
e). There should be a minimum of 2 inches (50.8mm) between the ground
and the fl oor of the remote LP cylinder enclosure.
f). The LP cylinder valve should be readily accessible for hand operation.
A door on the remote LP cylinder enclosure to gain access to the LP
cylinder valve is acceptable, provided it is non-locking and can be
opened without the use of tools.
If your licensed contractor or licensed plumber builds an LP cylinder enclosure
following the guidelines in the ANSI Standard for Outdoor Cooking Gas
Appliances,
Z21.58 CSA 1.6, you need to order kit number (#21287), which will contain the
hose and regulator assembly, mounting bracket for the regulator, connection
fi ttings and LP tank bracket for retaining the LP cylinder that must be used
with the Summit
®
Built-In gas grill. The hose and regulator in the kit (#21287) is
listed as part of the CSA listed Summit
®
Built-In gas grill.
ƽDANGER
Use of any other hose and regulator assembly could be
dangerous, and may not provide adequate gas supply
to the Summit
®
Built-In gas grill, and could result in a
fi re or an explosion causing serious bodily injury or
death, and damage to property.
ƽDANGER
Failure to use the Summit
®
Built-In Tank Cabinet for a
20 lb cylinder or failure to build a LP cylinder enclosure
for a 20 lb cylinder following the requirements for
ventilation, cylinder retention and separation of the LP
cylinder from a heat source, listed in the ANSI Standard
for Outdoor Cooking Gas Appliances, ANSI Z21.58 CSA
1.6, could be dangerous, and could result in a fi re or an
explosion causing serious bodily injury or death and
damage to property.
If you do not follow the DANGER statements exactly, the Warranty on the
Summit
®
Built-In gas grill will be voided.
GAS SUPPLY
ƽ ATTENTION: This product has been safety tested and
is only certifi ed for use in a specifi c country. Refer to
country designation located on outer carton.
These parts may be gas carrying or gas burning components. Please
contact Weber-Stephen Products Co., Customer Service Department for
genuine Weber-Stephen Products Co. replacement part(s) information.
ƽ WARNING: Do not attempt to make any repair to
gas carrying or gas burning components without
contacting Weber-Stephen Products Co., Customer
Service Department. Your actions, if you fail to follow
this product Warning, may cause a fi re or an explosion
resulting in serious personal injury or death and
damage to property.