Genesis Advanced Technologies 55274 Gas Grill User Manual


 
C-5
Gas Instructions
Safe handling tips for Liquid Propane
Gas Cylinders
Liquid Propane (LP) gas is a petroleum product as are
gasoline and natural gas. LP gas is a gas at regular
temperatures and pressures. Under moderate pressure,
inside a cylinder, LP gas is a liquid. As the pressure is
released, the liquid readily vaporizes and becomes gas.
LP gas has an odor similar to natural gas. You should
be aware of this odor.
LP gas is heavier than air. Leaking LP gas may collect
in low areas and prevent dispersion.
To fill, take the LP cylinder to an RV center, or look up
“gas-propane” in the phone book for other sources of
LP gas.
ƽ WARNING: We recommend that your LP cylinder be
filled at an authorized LP gas dealer, by a qualified
attendant, who fills the tank by weight. IMPROPER
FILLING IS DANGEROUS.
ƽ WARNING: If you exchange your LP cylinder, make
sure you get a similar tank in return. Your LP
cylinder is equipped with a quick closing coupling
or type 1 valve and an OPD (Overfilling Prevention
Device). Other LP cylinders may not be compatible
with your barbecue connection.
Air must be removed from a new LP cylinder before the
initial filling. Your LP dealer is equipped to do this.
The LP cylinder must be installed, transported and
stored in an upright position. LP cylinders should not be
dropped or handled roughly.
Never store or transport the LP cylinder where
temperatures can reach 125° F (too hot to hold by hand
- for example: do not leave the LP cylinder in a car on a
hot day).
Note - A refill will last about 20 hours of cooking time at
normal use. The fuel scale will indicate the propane supply
so you can refill before running out. You do not have to run
out before you refill.
Treat “empty” LP cylinders with the same care as when
full. Even when the LP tank is empty of liquid there still
may be gas pressure in the cylinder. Always close the
cylinder valve before disconnecting.
ƽ CAUTION: When transporting the LP cylinder make
sure the plastic dust cover is in place over the
valve. This will keep dust and dirt from the threaded
portion of the valve.
Do not use a damaged LP cylinder. Dented or rusty LP
cylinders or LP cylinders with a damaged valve may be
hazardous and should be replaced with a new one
immediately.
Liquid Propane (LP) Cylinder(s)
The joint where the hose connects to the LP cylinder
must be leak tested each time the LP cylinder is
reconnected. For example, test each time the LP
cylinder is refilled.
Be sure the regulator is mounted with the small vent
hole pointed downward so that it will not collect water.
This vent should be free of dirt, grease, bugs etc.
The LP cylinder and connections supplied with your
Weber
®
gas barbecue have been designed and tested
to meet government, American Gas Association, and
Underwriters Laboratories requirements.
Liquid Propane Cylinder requirements
Replacement LP cylinders supplied by Weber satisfy
the above requirements. Check to be sure other
cylinders have a D.O.T. certification(1), and date
tested(2) is within five years. Your LP gas supplier can
do this for you.
If you have questions about spare LP cylinders
contact the Customer Service Representative in your
region using the contact information sheet provided
with your manual.
All LP tank supply systems must include a collar to
protect the cylinder valve.
The LP cylinder must be a 20-lb. size (18 1/4 inches
high, 12 1/4 inches in diameter).
The LP cylinder must be constructed and marked in
accordance with the specifications for LP gas cylinders
of the U.S. Department of Transportation (D.O.T.).
For Canada Only
Liquid Propane Cylinder requirements
ƽ WARNING: Replacement LP tanks must match the
regulator connection supplied with this barbecue.
Note: Your retailer can help you match a replacement tank
to your barbecue
All LP tank supply systems must include a collar to
protect the cylinder valve.
The LP cylinder must be a 20-lb. size (18 1/4 inches
high, 12 1/4 inches in diameter).
The LP cylinder must be constructed and marked in
accordance with the specifications for LP gas cylinders,
T.C.
DOT 4BA240
00/01
(1)
(2)