Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
6
NOTE: IMPROPER LIGHTING PROCEDURES CAN CAUSE THE FLOW CONTROL
TO ACTIVATE, RESULTING IN REDUCED HEAT OUTPUT. IF THIS IS SUSPECTED,
RESET THE FLOW CONTROL BY SHUTTING OFF ALL BURNER CONTROLS AND
THE CYLINDER VALVE. WAIT 30 SECONDS, THEN TURN THE CYLINDER VALVE
ON EXTREMELY SLOWLY - WAIT 5 SECONDS AND TURN THE BURNER VALVE
ON AND LIGHT AS NORMAL.
• Never connect a propane gas barbeque to an unregulated propane gas
supply or any other gas. Do not attempt to alter the hose or regulator in
any way.
• The connection fitting must be protected when disconnected from the
propane tank. If the fitting is allowed to drag on the ground, nicks and
scratches could occur resulting in a leak when connected to the propane tank.
PROPANE AND NATURAL GAS MODELS:
• Do not allow any grease (or other hot material) to fall onto the hose, or
allow the hose to come in contact with any hot surfaces of the barbeque.
• Visually inspect the entire length of the hose assembly before each use
of the barbeque. If it is evident there is excessive abrasion/wear, or the
hose is cut, it must be replaced prior to using your barbeque. Only the
hose assembly as specified in the Parts List should be used.
• Follow the ‘LEAK TEST’ instructions before lighting your barbeque for
the first time, every time a propane cylinder is refilled, if any gas
component is changed, if the regulator flow-limiting device has been
activated, after prolonged periods of storage or non-use or at least once
per season.
NATURAL GAS MODELS:
• Never use with propane, or any other gases.
• The appliance and its individual shut-off valve must be
disconnected from the gas supply piping during any pressure
testing of the system at test pressure in excess of 3.5 kPa (1/2
p.s.i.).
• The appliance must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during
any pressure testing of the gas supply piping system at
pressures equal to or less than 3.5 kPa (1/2 p.s.i.).
• The gas supply hose must be a minimum of 3.1 m (10 ft) and a
maximum of 3.6 m (12 ft). Always disconnect hose at quick
connect coupling when storing your barbeque.
• Inspect and clean quick connect coupling, and keep it protected
when it’s not in use.
HOSE & REGULATOR
PROPANE GAS MODELS:
Your barbeque is designed to operate on L.P. (propane) gas at a pressure
regulated at 2.74 kPa (11" water column). A regulator preset to this pressure
is supplied with the barbeque and MUST be used.
This regulator is equipped with the Q.C.C. Type 1, quick connect coupling
system, which incorporates the following safety features: (Figure 5)
• It will not allow gas to flow until a positive seal has been made (Figure 6)
• It has a thermal element that will shut off the flow of gas between
115 and 150°C (240 and 300°F)
• It also has a flow-limiting device which, when activated, will restrict the flow
ofgas to 0.28 cubic metres per hour (10 cubic feet per hour)
Prior to attaching the propane cylinder to the hose and regulator, be sure the
cylinder valve and the appliance valves are OFF. The cylinder valve is turned
off by rotating the handwheel (see Figure 3) clockwise (left to right) until it
stops and all appliance valves should be in the twelve o'clock position. When
attaching the regulator to the cylinder, make sure that the small probe in the
nipple is centered in the mating Q.C.C. 1 cylinder valve (see Figure 6). Turn the
right hand threaded Q.C.C.1 black nut onto the valve in a clockwise motion until
there is a positive stop.
DO NOT USE A WRENCH, HAND TIGHTEN ONLY.
Should the large black thermally sensitive coupling nut be exposed to temperatures
above 115 - 150°C, it will soften and allow the regulator probe to disengage
from the cylinder valve – thereby shutting off the flow of gas. Should this occur,
do not attempt to reconnect the nut. Remove the entire regulator assembly,
and replace it with a new one.
The cause of the excessive heat should be determined and corrected
before operating your barbeque again. The regulator probe also contains a
flow-sensing element, which will limit the flow of gas to the regulator to a
manageable amount (0.28 cubic metres/hour) in the event of a hose or regulator
rupture. If it is evident that the flow control device has been activated, the
cause of the excessive flow should be determined and corrected before using
your barbeque again.
WARNING
FAILURE TO ENSURE THE ABOVE MAY RESULT
IN A HAZARDOUS FIRE OR EXPLOSION
CAUSING SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE.
WARNING
WARNING: INDICATES AN POTENTIALLY
HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY.
!
Fig. 5
Fig. 6
REGULATOR
REGULATOR
STRAIGHT
Q.C.C.I
Q.C.C.I
WARNING
DO NOT ATTEMPT TO REPAIR OR ALTER THE
HOSE/VALVE/REGULATOR FOR ANY "ASSUMED"
DEFECT. ANY MODIFICATION TO THIS ASSEMBLY
WILL VOID YOUR WARRANTY AND CREATE THE
RISK OF A GAS LEAK AND FIRE. USE ONLY
AUTHORIZED REPLACEMENT PARTS SUPPLIED BY
MANUFACTURER.
!