Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
9
103573
OWNER’S MANUAL
Rear Hole
INSTALLING FIREPLACE
SCREEN
1. Insert each rod through nine rings lo-
cated at top of screen.
2. Insert first rod into rear hole in left side
of firebox. Fasten rod to rear hole near
center of firebox using black shoulder
screw.
3. Insert other rod into front hole on right
side of firebox and fasten using remain-
ing shoulder screw.
Rod
Front Hole
Ring
Screen
Screw
Figure 11 - Installing Fireplace Screen
Continued
FIREBOX INSTALLATION
USING OPTIONAL
ACCESSORY MANTELS
This firebox may be installed using the cabi-
net mantel and hearth base accessories against
a wall in your home. Follow the instructions
below to install the firebox in this manner.
Note:
The instructions below show installa-
tion using GMC11F/GMC12U/GMC13F
series cabinet mantels and the GC3333F/
GC3334U/GC3335F series hearth base ac-
cessories. The hearth base accessory shown
is optional for this installation. You can
install firebox and cabinet mantel directly
on the floor.
Electrical
Outlet
Hearth Base
Flexible Gas Line
Gas
Line
Access
Hole
Figure 12 - Placing Hearth Base
Accessory Against Wall
Nailing
Flanges
Cabinet
Mantel
Figure 13 - Installing Cabinet Mantel
Figure 14 - Location of Nailing Flanges
9. Attach flexible gas line to log set. See
Connecting to Gas Supply in your log
set owner’s manual.
10. If installing GA3750 blower, route
blower electrical cord through bushing
in right side firebox support and bush-
ing in side access opening of firebox.
Plug electrical cord into electrical out-
let. See Installing Blower Accessory,
page 8.
11. Carefully insert firebox into cabinet man-
tel. Be careful not to scratch or damage
cabinet mantel or hearth base. Remove
protective material from top of hearth
base and from front of firebox (if any).
12. Install the trim after final finishing and/
or painting of wall. See instructions in-
cluded with mantel accessory for at-
taching brass trim.
13. Check all gas connections for leaks. See
Checking Gas Connections in log set
owner's manual.
INSTALLATION
Continued
1. Assemble cabinet mantel, hearth base,
and perimeter trim (Included with man-
tel). Assembly instructions are included
with each accessory.
2. If using an optional GA3750 blower,
install a properly grounded, 120 volt
three-prong electrical outlet at firebox
location if an outlet is not there. If pos-
sible, locate outlet so cabinet mantel will
cover it when installed (see Figure 13).
3. Install gas piping to firebox location. This
installation includes an approved flex-
ible gas line (if allowed by local codes)
and a manual shutoff valve. The flexible
gas line must be the last item installed
on the gas piping. See Connecting to Gas
Supply in your log set owner’s manual.
WARNING: A qualified ser-
vice person must connect fire-
box to gas supply. Follow all lo-
cal codes.
4. Place hearth base accessory against wall
at installation location. Cut an access
hole in hearth top to run flexible gas line
to firebox (see Figure 12). Make sure to
locate access hole so cabinet mantel will
cover it when installed.
Note:
You can
secure base to floor using wood screws.
Countersink screw heads and putty over.
5. Route flexible gas line through access
hole in hearth base.
6. Center cabinet mantel on hearth base
(see Figure 13). Make sure mantel is
flush against wall.
7. Break off nailing flanges (see Figure
14) with hammer or pliers.
8. Place cardboard or other protective
material on top of hearth base. Care-
fully set firebox on protective material,
with back of firebox inside mantel
opening.