Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
NON-COMBUSTIBLE MATERIAL AND MUST BE AT LEAST 30”
AWAY FROM ANY COMBUSTIBLE MATERIAL.
15
INFRA-BROIL REAR BURNER
The PGS Infra-Broil Kit comes as a standard feature on our models
Newport Gourmet and Pacifica Gourmet. The Infra-Broil is a rear
burner especially designed for those back yard chefs who love to
rotisserie. It features 12,000 BTU of radiant heat for extremely
efficient roistering. It will cook poultry and beef quickly and
efficiently to perfection every time!
Please note, when using the Infra-Broil Burner,
you should never have any of the lower burners
on. Using any other lower burner at the same
time as a rear burner poses potential problem
with insufficient oxygen, which could cause rear
burner to go out and cause a gas leak.
To operate, turn far right hand knob with the word “ROTIS” under it
to the “HI” position. Push Sure Start Ignition button. Burner
should light within five seconds.
IF THE BURNER FAILS TO LIGHT, IMMEDIATELY TURN CONTROL OFF
TO PREVENT GAS BUILD-UP. WAIT FIVE MINUTES FOR GAS TO
CLEAR AND TRY THE ABOVE PROCEDURE AGAIN. IF THE BURNER
DOES NOT LIGHT WITH THE ELECTRONIC IGNITION, LIGHT THE
BURNER WITH A MATCH OR OTHER HAND HELD IGNITOR. TOUCH
LIGHTED MATCH OR HAND HELD IGNITOR TO THE LOWER RIGHT
HAND SIDE OF THE “INFRA-BROIL”.
Manual Lighting of Infra-B oil Rear Burner r
Rotisserie motor mount should be installed on the left hand side of the
Hood Support Brackets.
Please use care when operating electric rotisserie motor and
be certain that outlet used is grounded and incorporates a
Ground Fault Interrupter. When operating, be sure to keep
cord away from all liquids and hot surfaces.
When using Infra-Broil back burner, we suggest that you remove the
cooking grid and place a metal pan directly on the rock. We
suggest that you fill pan a minimum of one quarter full with liquid and
that you regularly check pan to ensure liquid remains during the entire
rotisserie cooking.
Masonry Cutouts
Model Height Depth Width
Newport 9 ½” 23” 28”
Newport Gourmet 9 ½” 23” 28”
Pacifica 9 ½” 23” 36 ½”
Pacifica Gourmet 9 ½” 23” 36 ½”
Side Burner Kit 9” 18 ½” 12 ½”
MDS (door kit) 16 ¾” 27 ½”
A counter balance is included with your PGS rotisserie kit, we suggest
positioning it so that it is opposite of your meat, to balance the load on
your motor.
SIDE BURNER KIT
A great optional accessory to compliment your PGS Legacy grill is our
high output “Infra-Red” Side Burner Kit. This will allow you to keep
all the mess and heat outside when grilling. You can boil water for
corn on the cob, lightly sauté creams or vegetables, simmer sauces for
basting your meal or any other task that you could do on your range in
the kitchen.
Side Burner Kit for the portable cart is attached to the RIGHT HAND
SIDE on your portable cart with (4) four screws included in the cart
shelf bracket kit. Two people are needed to accomplish this.
Remove packaging. Have one person hold the side burner in place
while the other starts all four screws. When all four screws are
started, tighten all. As an alternative, you may wish to attach the
side burner kit prior to placing grill head in cart. Simply lay cart
down on a padded surface on its’ left hand side. Side burner can
now be mounted on right hand side of cart with four screws included
to attach side shelf kit. PLEASE NOTE, SCREWS FOR SIDE
BURNER SHOULD NOT BE TIGHTENED UNTIL AFTER GRILL
HEAD IS PLACED ON CART. BATTERY IS PLACED WITH “+”
FACING OUT.
If Natural Gas, attach a flexible gas feed line to 3/8” male flare fitting
found on the underside of the side burner kit. Tighten fitting.
Feed balance of flexible gas feed line through hole in side of cart.
Remove brass accessory cap that is part of the natural gas regular, and
screw feed line to this assembly. See picture below:
Natural Gas Connection between Flex Connector
and Regulator Assembly
If LP, feed long section on 2 way hose and regulator combo through
hole in right hand side wall of cart. Connect Brass fitting to 3/8”
male flare fitting found on the underside of the side burner kit.
Tighten fitting. Attach short section of hose coming off regulator to
gas grill supply. Connect regulator to LP tank