Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
Warning: Before proceeding with
the following steps, ensure you
have read the L.P. Gas Cylinder
hose and Regulator sections of this
Assembly and Operation Manual.
Follow all directions under L.R Gas
Cylinder filling section of this
manual.
LIGHTING
Prior to lighting your grill,
visually check all hoses Middle Burner
before each use for nicks,
cracking, abrasions or cuts. Left Burner
If the hose is found to be Right Burner
damaged in any way, DO
NOT USE YOUR GRILL.
A replacement hose and
regulator is required (see
'PARTS LIST' in back of
book).
IMPORTANT
• Always raise the grill lid
before lighting. -- HIGH
• Do not lean over the grill -- LOW
when lighting the burner.
• Visually check the flames
every time you light your
grill (Figure 8). If the flame is abnormally small or smokey
yellow -- shut off the grill and check the venturi tubes for
blockage (see Figure 11 on pg. 27) or refer to the
Troubleshooting Guide.
On grills with Three burners, the right control knob operates
the right burner, the left knob operates the left burner, and the
center knob operates the center burner.
I
USING THE AUTO IGNITOR
Read these instructions before igniting.
1. Open lid during lighting.
2. Turn off all burners and close tank valve.
3. Open tank valve, wait 5 seconds.
4. Turn required burner knob to "IGNITE".
5. You should hear a "clicking sound" indicating your electronic
ignition is activated.
6. If the burner does not light immediately (within four
seconds), turn burner control knob off and wait 5 minutes to
clear the gas.
7. Repeat steps 1 to 7. If burner still fails to light, refer to
Troubleshooting Guide to determine cause and solution,
or try the Match Lighting Procedure.
8. After grill lights, turn knob to desired cooking position.
MATCH LIGHTING PROCEDURE
1.Open the lid before lighting
2. Place an ignited lighter or lit match through the lighting hole.
(See Figure 9)
3. Push in and turn the LEFT burner control knob to 'HIGH'.
The burner should light immediately (within four seconds). If
it does not, extinguish the lighter or match, turn the-control
knob to off, and wait 5 minutes to clear the gas.
4. Repeat steps 1 to 3. If burner fails to light, refer to the
Troubleshooting Guide to determine cause and solution.
5. Once left burner is lit push in and turn center burner knob
_gl_.gh. Once it is lit, push in and turn right burner knob to
SIDE BURNER
1. Open UP. cylinder.
2. Push in and turn the side burner control knob to "HI".
3. Depending on which ignitor you have, turn or depress
ignitor. Repeat if necessary.
4. If burner does not light immediately (within four seconds),
turn the burner control knob off, and wait 5 minutes to clear
the gas.
5. Repeat steps 1 to 4. If burner still fails to light, refer to the
Troubleshooting Guide to determine cause and solution, or
try the Match Lighting Procedure above.
USING THE AUTO IGNITOR
1. Open tank valve, wait 5 seconds.
2. Turn required burner knob to
"IGNITE".
3. You should hear a "clicking sound" indicating your
electronic ignition is activated.
4. If burner does not light immediately (within four seconds),
turn the burner control knob off, and wait 5 minutes to clear
the gas.
5. Repeat steps 1 to 5, if burner fails to light, refer to the
Troubleshooting Guide to determine cause and solution, or
try the Match Lighting Procedure above.
6. After grill lights turn knob to desired cooking position.
MATCH LIGHTING PROCEDURE
1. Place an ignited lighter or lit match near the ports,
approximately 1/2" (1.25 cm) from burner.
2. Push in and turn the side burner control knob to 'HIGH'. The
burner should light immediately (within four seconds). If it
does not, extinguish the lighter or match, turn the control
knob off, and wait 5 minutes for the gas to clear.
3. Repeat steps 1 and 2. If burner still fails to light, refer to the
Troubleshooting Guide to determine the cause and solution.
LOW HEAT OUTPUT
If the heat output from the burner(s) seems abnormally low,
it may be caused by the regulator flow-limiting device being
activated by a leak in the gas system, or improper lighting
procedures. If this is suspected, shut off the cylinder valve and
all burner valves. Perform a leak test to determine if a leak has
caused the flow-limiting device to activate. If the leak test is
negative, then carefully follow the lighting procedures step-by-
step, ensuring all valves (including tank) are off before starting.
RELIGHTING
If the burner flame goes out when your grill
is in operation, immediately turn off the
control valves. Wait five minutes for the gas
to clear before attempting to relight the I
burner. If the problem persists, refer to the
troub eshoot ng gu de
SHUTTING DOWN YOUR GRILL
1. Shut off L.P. cylinder valve or natural gas main shut-off valve.
2. Shut off burner control valves.
This sequence prevents residual gas from being left in the
system under pressure.
25