Filter
Top Products
Special offers from our partners!
Find Replacement BBQ Parts for 20,308 Models. Repair your BBQ today.
INSTRUCTIONS:
1. Remove original head as described in your trimmer Operator’s Manual.
2A. For machines with extended threaded shafts (A) select triangular adaptor (C) that most closely
matches diameter of the threaded shaft. Select the correct nut (D) thread size and tightening
direction. Refer to Application Chart on page 5 and bag content list below to select correct
hardware for your specific model.
2B. For machines with threaded holes (B) select the correct size bolt (E) that threads into the gear
box. Then select triangular adaptor (C) that most closely matches the diameter of the bolt.
2C. For Stihl FS straight shaft models and Husqvarna 300 Series, mount Rapid Loader
TM
head (G)
directly over one inch shoulder on -bottom of gear box. Place nylon spacer (J), and nut (D)
into center of Rapid Loader
TM
head (G) and tighten securely.
Disregard steps 3~6.
3. Place the large washer (F) between the bottom of the gear box and the trimmer head (G).
4. Place the black triangular adaptor (C) into the center recess of the Rapid Loader
TM
head (G) and
align the triangle boss with triangle opening in recess.
5. Thread the selected nut (D) or bolt (E) into the center of the Rapid Loader
TM
head (G) and tighten
securely.
6. Insert pre-cut 204 mm (8 in.) length of nylon cutting line (recommended sizes 2.4 mm [.095 in.]
to 3.9 mm [.155 in.]) through outside openings of trimmer head. Minimum of 153mm (6 in.) of
line should extend from each opening. 3.9mm [.155 in.] line not recommended for trimmers
under 26cc.
NOTE
Insertcuttinglineendstocenterofheadrecesstoinsureeasyremovalofusedlines.
2
A
B
21560057(REF#RL-35) ADAPTERSOLDSEPARATELYFORSTIHLFSCURVEDSHAFTTRIMMERS.
ContactyourECHODealertoorderRapidLoader
TM
pre-cutreplacementline.
ORANGEBAGCONTENTLIST
REF# COLOR DESCRIPTION
RL52 SILVER 10
mmX1.25X22LEFTHANDBOLT
RL53 GOLD 8
mmX1.25X22LEFTHANDBOLT
RL70 BLUE 8
mmX1.25LEFTHANDNUT
RL72 BLACK 10
mmX1.00LEFTHANDNUT
RL74 GOLD 10
mmX1.25LEFTHANDNUT
RL77 SILVER 3/8-24LEFTHANDNUT
RL78 RED
(InGreeenBag)
3/8-24RIGHTHANDNUT
RL42 SILVER 3/8X1.5IN.LARGEFENDERWASHER
RL45 SILVER 3/8X1.25IN.SMALLFENDERWASHER
GREENBAGCONTENTLIST
Tobeusedwiththreepieceadapter(REF#RL-30).
COLOR DESCRIPTION
GOLD 8
mmX1.25RIGHTHANDNUT
SILVER 5/16-20X1RIGHTHANDBOLT
SILVER 1/4-20X1/2RIGHTHANDBOLT
SILVER 5/16-24RIGHTHANDNUT
SILVER 3/8FLATWASHER
IMPORTANT
Donotforceboltsornutsontotrimmershaft,otherwisedamagetotrimmerthreadsmayoccur.
C
D
E
F
G
J
Trimmer Line Diameter Usage
All curved Shaft Line Trimmers Use Line Diameter .080” To .095”
Line Trimmers Engine Size 15cc. To 24CC. Use Line Diameter .095” To .105”
Line Trimmers Engine Size 25cc. & UP Use Line Diameter .095” To .155”