Vanguard Managed Solutions MBDV41 Outdoor Fireplace User Manual


 
17
106497
OWNER’S MANUAL
FIREPLACE
INSTALLATION
Continued
WARNING: Never touch the
blower wheel while in operation.
WARNING: Failure to position
the parts in accordance with sup-
plied diagrams or failure to use
only parts specifically approved
with this heater may result in dam-
age or personal injury.
WARNING: A qualified ser-
vice person must connect fire-
place to gas supply. Follow all
local codes.
Figure 32 - Attaching Speed Control to
Firebox
Figure 33 - Installing Plastic Bushing
Wiring
Diagram
Continued
Blower Speed Control Bracket
BLOWER ASSEMBLY AND
OPERATION
Note:
The blower is preinstalled in this
fireplace. Verify blower assembly place-
ment was not altered during shipping and
speed control is mounted to bracket.
NOTICE: If installing blower in an
existing fireplace with gas con-
nections, shut off gas supply and
disconnect heater from gas sup-
ply. Contact a qualified service
person to do this.
Installing GA3700 Blower
(Some Models Have Blower
Assembly Preinstalled)
IMPORTANT
: For clarity, gas valve assem-
bly and grate/burner assembly are not shown
in Figures 31 through 33. They will, how-
ever, be in your fireplace when you are in-
stalling the blower. Also for clarity the fire-
box is shown with dotted lines.
1. Open lower louver panel or remove for
easier access.
2. Place the blower against the lower rear wall
of firebox outer wrapper with the exhaust
port directed upward. Align the holes in
the top mounting tabs of blower with holes
in wall of wrapper (see Figure 31). Using
the two screws provided, mount blower
and tighten screws securely.
3. Be sure to securely attach all wire ter-
minals to terminals on blower motor
and that the screw retaining the green
ground wire is tight.
4. Remove screws securing the plate con-
taining the ON/OFF switch to the bot-
tom of the firebox and set aside.
5. Place speed control against back of this
plate and push the plastic control shaft
through opening (see Figure 32).
6.
While supporting speed control, secure con-
trol shaft with lock nut by pushing and turn-
ing lock nut with pliers clockwise until tight
against the plate. Place control knob pro-
vided onto shaft (see Figure 32).
7. Replace plate containing switches and
tighten screws securely.
8. Plug in blower power cord.
a. If your fireplace system is installed
as a freestanding unit with an ac-
cessory mantel, determine whether
the power cord will exit the left side
or the right side of the firebox. In-
stall one plastic bushing provided
into the 1
1
/2" hole in the outer cas-
ing through which the power cord
will exit. Install the second plastic
bushing provided into the floor sup-
port bracket if exiting through the
right side (see Figure 33). Route
power cord through (both) plastic
bushing(s) and plug the power cord
into a properly grounded 3-prong
wall receptacle near the firebox.
b. If your fireplace system installation
is recessed and/or pre-wired, a
qualified installer must make all elec-
trical connections for the outlet kit
included with the fireplace.
9. Check to make sure that the power cord
is completely clear of the blower wheel
and that there are no other foreign ob-
jects in blower wheel. Turn blower on
and check for operation. Turn blower
off by rotating knob fully counterclock-
wise before continuing.
10. Connect or reconnect gas supply to fire-
place per Connecting Fireplace to Gas
Supply on page 20 of this manual.
Figure 31 - Mounting Blower to Firebox
Top
Mounting
Tab
Exhaust Port
Screws
Blower
Lower Louver
Panel
Lower Rear
Wall of
Firebox
Wrapper
Control Knob
Locknut
Control Shaft
Speed Control
Plastic Bushing