![](http://pdfasset.owneriq.net/a/84/a8463596-2d37-4aaa-9973-141683b11585/a8463596-2d37-4aaa-9973-141683b11585-bg1.png)
Setting Values Cross Reference Table
(The tire size is marked on both sides of the tire.)
U.S. Pat. Nos. 4636769/4642606/5236759/5226340
and Design Patented
Copyright© 1999 CATEYE Co., Ltd.
CCMSTxch1-991124 Printed in Malaysia 066600035
3
CATEYE TOMO XC
CYCLOCOMPUTER
Model CC-ST200
[with Heavy Duty Wire]
magnet
sporkes
bracket
rubber pad
Fig.1
Fig.8
MOUNTING TO BIKE
Fig.9
lever
#169-9731
Heavy Duty Wire and Bracket Sensor Kit
#169-9771
Bracket Sensor Kit for Extra Large Fork
#169-6168
Bracket Sensor Kit for Aero Bar
#169-6167
Center Mount Bracket Kit
#169-6169
Stem Mount Bracket Kit
#169-9750 #169-9751
Attachment Kit (For Heavy Duty Wire) Attachment Kit (For TOMO XC)
#166-5120 #169-6180
Wheel Magnet Lithium Battery(CR1620)
SPECIFICATIONS
Controller ----------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)
Display --------------------------------------Liquid Crystal Display
Sensor --------------------------------------No Contact Magnetic Sensor
Operating Temperature Range -------0°C - 40°C (32°F - 104°F)
Applicable Cycle Sizes------------------130cm - 229cm
The length of the wire -------------------70cm
Applicable Fork Diameter --------------11ø - 40ø (S:11 - 26ø L:21 - 40ø)
Power Supply -----------------------------Lithium Battery (CR1620 or CR1616) x 1
Battery Life ---------------------------------Approx. 3 years(The life of the first factory-loaded battery may
be shorter than this period.)
Dimension/Weight------------------------1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g)
* The specifications and design are subject to change without notice.
LIMITED WARRANTY
1-Year Warranty for Main Unit Only
(Accessories/Attachments and Battery Consumption excluded)
If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of
charge. The service must be performed by Cat Eye Co., Ltd. To return the product, pack it carefully
and remember to enclose the warranty certificate with instruction for repair. Please write or type your
name and address clearly on the warranty certificate. Insurance, handling and transportation charges
to our service shall be borne by person desiring service.
(Address for service)
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn.: CAT EYE Customer Service Section
Service & Research Address for United States Consumers:
CAT EYE Service & Research Center
1705 14th St. 115 Boulder, CO 80302
Phone: 303-443-4595 Toll Free: 800-5CATEYE
Fax : 303-473-0006 e-mail: CatEyeUSA@aol.com
CO
.,LTD.
E
Slide the main unit onto the bracket from
front until it clicks into position. To remove
it, pull it off forward while pushing down the
lever. (Fig.9)
• The spokes must run correctly through the
inside the magnet as in fig.1.
• Attach the sensor with Sensor Bands-A-B to
the right fork. Choose a band that fits the fork
diameter (S size for up to 24ø, L for
oversize). If the front fork is thick, use the
longer screw.
1. Insert the band-B into the slit of the band-
A, and put the rubber pad inside of the
band-A(fig. 2). Adjust the length in order
that the screw-fastening part of the bands
are parallel when mounted to the fork(fig.
3). *To pull out the band B from band A,
tug strongly.
2. Mount the adjusted bands to the fork along
with the sensor, by temporarily tightening
the screw(fig. 4).
3. Align the magnet's center and the sensor's
marking line(fig. 5), and make sure of
2mm clearance between the magnet and
sensor (fig. 6). Then tighten the screw
securely. Cut the excess of the band-B
with a nipper or the like.
• Secure the wire with nylon ties as shown in
fig. 7. Wind the wire round the outer cable
and wrap these wires with the spiral tube.
Adjust the length of the wire. Loosen the wire
in the area marked with the arrow so that the
wire does not hinder handlebar operation.
• Use either 1mm- or 2 mm-thick pads if
necessary, according to handlebar diameter.
Attach the bracket close to the handlebar
stem (fig. 8).
• Slide main unit onto the bracket from front
until it clicks into position. To remove, pull it
off forward while pushing down the lever. (fig.
9)
•Test
Mount main unit. If main display does not show
any figures, press either M button or S/S button
to release from power saving function. Spin the
wheel to check if sensor pulse symbol flashes.
If not, adjust relative positions of magnet and
sensor following the instructions.
TIRE SIZE L(cm) TIRE SIZE L(cm) TIRE SIZE L(cm)
20 x 1.75 150 26 x 1.40 200 650 x 38B 211
24 x 1 175 26 x 1.50 199 700 x 18C 207
24 x 3/4 Tubular 178 26 x 1.75 202 700 x 19C 209
24 x 1-1/8 Tubular 179 26 x 1.95 205 700 x 20C 209
24 x 1-1/4 191 26 x 2.00 206 700 x 23C 210
24 x 1.75 189 26 x 2.1 207 700 x 25C 211
24 x 2.00 192 26 x 2.125 207 700 x 28C 214
24 x 2.125 196 26 x 2.35 208 700 x 30C 217
26 x 1(559mm) 191 27 x 1 215 700 x 32C 216
26 x 1(650c) 195 27 x 1-1/8 216 700C Tubular 213
26 x 1.25 195 27 x 1-1/4 216 700 x 35C 217
26 x 1-1/8 Tubular 197 27 x 1-3/8 217 700 x 38C 218
26 x 1-3/8 207 650 x 35A 209 700 x 44C 222
26 x 1-1/2 210 650 x 38A 212
nyron ties
Fig.7
outer cable
wire
spiral tube
Fig.5
markingline
of sensor
center of
magnet
sensor band B
sensor
band A
Fig.3
rubber pad
sensor band B
Fig.4
sensor band A
Fig.2
screw
magnet
sensor
Fig.6
rubber pad
parallel
sensor
about 2mm
fork
sensor band A
1. Bracket
2. Wire
3. Sensor
4. Sensor Bands-A (S)(L)
5. Sensor Bands-B
6. Magnet
7. Sensor Band Rubber Pad
8.
Bracket Rubber Pad (2 pcs.)
9. Nylon Tie (3 pcs.)
10. Sensor Band Screw (S)(L)
11. Spiral Tube